{"title":"Chassis \u0026 Axle Conversion","description":"\u003cp\u003eFrame sections, front- and back-half kits, wheelbase-stretch kits, full-width axle conversions, and dedicated axle-swap systems for custom off-road builds. Check each product for vehicle and donor-axle compatibility, required supporting parts, and cutting or welding requirements. Standalone reinforcement plates are components, not complete conversion kits.\u003c\/p\u003e","products":[{"product_id":"motobilt-mb1500","title":"Jeep YJ Wheelbase Stretch Kit Motobilt","description":"\u003cp\u003eThe Motobilt Jeep Wrangler YJ Wheelbase Stretch Kit is a great way to move your rear axle back roughly 6 inches. The Motobilt Jeep Wrangler Wheelbase Stretch Kit is designed to use Jeep XJ rear leaf springs on the rear of your Jeep YJ (1987-1995). Installing this kit moves the rear axle back about 6 inches. The kit incorporates a custom rear bumper and shackle hangers in one part. The shackle hangers are positioned high on the bumper to keep the overall Jeep ride height lower for better center of gravity. The ends of the bumper are tapered in to allow better clearance for the shackles with the rear axle at full droop.\u003c\/p\u003e\n\u003cp\u003eThe kit comes with a custom set of leaf spring shackles designed to clear the bumper in the range of movement. The rear bumper also features 3\/4 inch thick d-ring recovery mounts that pass through the bumper and welded on both sides. The bumper welds to the back of the factory cross member and has two side frame plates to cover the sides. This kit does include new spring shackles as noted. The shackles are CNC laser cut from 1\/4 inch high strength steel plate. The shackles measure 4 inches center to center and do have a 3rd cross bolt for additional support.\u003cbr\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJeep Wrangler YJ Wheelbase Stretch Kit\u003c\/li\u003e\n\u003cli\u003e1987-1995 Jeep Wrangler YJ\u003c\/li\u003e\n\u003cli\u003eThe bumper is 3\/16 inch laser cut steel plate\u003c\/li\u003e\n\u003cli\u003e3\/4 inch thick d-ring mounts\u003c\/li\u003e\n\u003cli\u003eIncorporated shackle mounts\u003c\/li\u003e\n\u003cli\u003eMoves the axle back 6 inches\u003c\/li\u003e\n\u003cli\u003eMeasures 42.5 inch wide\u003c\/li\u003e\n\u003cli\u003eIncludes new shackles and shackle spacer\u003c\/li\u003e\n\u003cli\u003eSold as kit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePurchase PN BushingKit if you require the shackle bushing kit\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271370944683,"sku":"MB1500-HJQL","price":469.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB1500-HJQL_3504b6f0-2337-463a-814a-1e049f6092f0.jpg?v=1792076481"},{"product_id":"motobilt-mb1519","title":"Jeep CJ Wheelbase Stretch Kit Motobilt","description":"\u003cp\u003eThe Motobilt Jeep CJ Wheelbase Stretch Kit is designed to use Jeep XJ rear leaf springs on the rear of your Jeep CJ (1976-1986). Installing this kit moves the rear axle back about 6 inches. The kit incorporates a custom rear bumper and shackle hangers in one part. The shackle hangers are positioned high on the bumper to keep the overall Jeep ride height lower for better center of gravity. The ends of the bumper are tapered in to allow better clearance for the shackles with the rear axle at full drop.\u003c\/p\u003e\n\u003cp\u003eThe kit comes with a custom set of leaf spring shackles designed to clear the bumper in the range of movement. The rear bumper also features 3\/4 inch thick d-ring recovery mounts that pass through the bumper and welded on both sides. The bumper welds to the back of the factory cross member and has two side frame plates to cover the sides. This kit does include new spring shackles as noted. The shackles are CNC laser cut from 1\/4 inch high strength steel plate.\u003c\/p\u003e\n\u003cp\u003eThe shackles measure 4 inches center to center and do have a 3rd cross bolt for additional support. The kit does not include poly bushings. The kit does require removing the factory gas tank. Many people install an aftermarket fuel cell.\u003cbr\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJeep CJ Wheelbase Stretch Kit\u003c\/li\u003e\n\u003cli\u003eFit 1976-1986 Jeep CJ\u003c\/li\u003e\n\u003cli\u003eThe bumper is 3\/16 inch laser cut steel plate\u003c\/li\u003e\n\u003cli\u003e3\/4 inch thick d-ring mounts\u003c\/li\u003e\n\u003cli\u003eIncorporated shackle mounts\u003c\/li\u003e\n\u003cli\u003eMoves the axle back 6 inches\u003c\/li\u003e\n\u003cli\u003eMeasures 38 inch wide\u003c\/li\u003e\n\u003cli\u003eSold as kit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eHardware kit sold separately\u003c\/li\u003e\n\u003cli\u003eShackle bushing kit sold separately PN BushingKit\u003c\/li\u003e\n\u003cli\u003eIncludes new shackles and shackle spacers\u003c\/li\u003e\n\u003cli\u003eThe kit does require removing the factory gas tank\u003c\/li\u003e\n\u003cli\u003eMany people install an aftermarket fuel cell\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271425339563,"sku":"MB1519-HJQL","price":469.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB1519-HJQL_ce4dcc78-6876-4296-a6a9-2097f53cd168.jpg?v=1792077143"},{"product_id":"motobilt-mb3004","title":"Jeep CJ Rear Cross Member 76-86 Jeep CJ Bare Steel Motobilt","description":"\u003cp\u003eThe Motobilt rear Jeep CJ (1976-1986) cross member is a perfect solution for those wanting to replace a bent or rusted out factory rear cross member. Over the years we have seen many Jeep Wrangler CJ's needing a replacement for the rear cross member. Often times due to someone attaching a snatch strap or chain to the thin factory Jeep cross member.\u003c\/p\u003e\n\u003cp\u003eOther cases have been due to rust. Either way the Motobilt rear cross member is a great alternative to simply installing a factory cross member. The Motobilt cross member is fabricated from heavy duty 3\/16 inch steel plate. The rear cross member retains the factory bolt holes for the rear bumper and gas tank skid.\u003c\/p\u003e\n\u003cp\u003eThe cross member also provides mounting holes for the factory corner body mount bushings. The cross member ships ready to install. Installation does require welding. It is highly recommended using a professional welder for the installation. The cross member is shipped out bare steel ready to install.\u003cbr\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJeep CJ rear cross member\u003c\/li\u003e\n\u003cli\u003eFits 1976-1986 Jeep CJ\u003c\/li\u003e\n\u003cli\u003eFabricated from heavy duty 3\/16 inch steel plate\u003c\/li\u003e\n\u003cli\u003eCross member retains the factory bolt holes for the rear bumper and gas tank skid\u003c\/li\u003e\n\u003cli\u003eSold as each\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eShips ready to install\u003c\/li\u003e\n\u003cli\u003eRequires welding\u003c\/li\u003e\n\u003cli\u003eHighly recommended using a professional welder for the installation\u003c\/li\u003e\n\u003cli\u003eShips bare steel\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271442444459,"sku":"MB3004-HJQL","price":169.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB3004-HJQL.jpg?v=1792077359"},{"product_id":"motobilt-mb3003","title":"Jeep TJ Rear Cross Member 97-06 Wrangler TJ Bare Steel Motobilt","description":"\u003cp\u003eThe Motobilt rear Jeep TJ (1997-2006) cross member is the strongest available. We base this claim because we did not simply use thicker material we also added gusseting to the cross member. The original intent was in designing a cross member for a customer who wanted to run it as a high clearance rear bumper.\u003c\/p\u003e\n\u003cp\u003eOver the years we have seen many Jeep Wrangler TJ's needing a replacement for the rear cross member. Often times due to someone attaching a snatch strap or chain to the thin factory Jeep cross member. Other cases have been due to rust. Either way the Motobilt rear cross member is a great alternative to simply installing a factory cross member. The Motobilt cross member is fabricated from heavy duty 3\/16 inch steel plate. The rear cross member retains the factory bolt holes for the rear bumper and gas tank skid.\u003c\/p\u003e\n\u003cp\u003eThe cross member also provides mounting holes for the factory corner body mount bushings. The cross member ships full welded and ready to install. Installation does require welding. It is highly recommended using a professional welder for the installation. The cross member is shipped out bare steel ready to install.\u003cbr\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJeep TJ rear cross member\u003c\/li\u003e\n\u003cli\u003eFits: 1997-2006 Jeep TJ\u003c\/li\u003e\n\u003cli\u003eFabricated from heavy duty 3\/16 inch steel plate\u003c\/li\u003e\n\u003cli\u003eCross member retains the factory bolt holes for the rear bumper and gas tank skid\u003c\/li\u003e\n\u003cli\u003eSold as each\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eShips full welded and ready to install\u003c\/li\u003e\n\u003cli\u003eRequires welding\u003c\/li\u003e\n\u003cli\u003eHighly recommended using a professional welder for the installation\u003c\/li\u003e\n\u003cli\u003eShips bare steel\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271442509995,"sku":"MB3003-HJQL","price":259.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB3003-HJQL.jpg?v=1792077360"},{"product_id":"motobilt-mb2087","title":"Chassis Frame Fish Plate Approximately 5x 3 Inch Motobilt","description":"\u003cp\u003eThe Motobilt Chassis Frame Fish Plate is universal and can be bent or formed to whichever angle you are working with. Chassis Frame Fish Plate is CNC Laser cut out of 3\/16 inch P and O steel is approximately 5 inch x 3 inch.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eChassis Frame Fish Plate\u003c\/li\u003e\n\u003cli\u003eCNC Laser cut out of 3\/16 inch P and O steel\u003c\/li\u003e\n\u003cli\u003eApproximately 5 inch x 3 inch\u003c\/li\u003e\n\u003cli\u003eSold as each\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271443919019,"sku":"MB2087-HJQL","price":3.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB2087-HJQL.jpg?v=1792077402"},{"product_id":"motobilt-mb3020-s","title":"Jeep LJ Frame Back Half Kit W\/Stubby Bumper 04-06 Wrangler TJ Unlimited Motobilt","description":"\u003cp\u003eThe Motobilt Jeep LJ back half kit is the most complete on the market. This kit replaces the back section of frame rails to allow space to clear coilover shocks and increase departure angle. How does the the Jeep LJ back half kit do this? The Motobilt kit moves the frame rails from inside the wheel opening to the bottom side of the tube. In doing so the bumper location is moved up to just below the tailgate. This kit requires an experienced welder\/fabricator to install.\u003c\/p\u003e\n\u003cp\u003eBuilding custom four link suspension on a Jeep LJ does not have to be difficult. The Motobilt Jeep LJ back half kit is an effective way to gain clearance for suspension components like coilovers shocks, bypass shocks, or ORI struts. The Jeep LJ Back Half Kit moves the frame rails to the bottom side of the tube. The frame rails will mount directly to the bottom side of the rear floor board for a tight compact fit. It should be noted the kit requires cutting sheet metal on the body just below the tailgate to allow the frame rails to extend out. The bumper is then attached in this new location. The Motobilt kit comes complete with a rear bumper.\u003c\/p\u003e\n\u003cp\u003eWhat does the Motobilt Jeep LJ back half kit include? The kit includes 7 parts total in the shipment. Two lower frame rails sections and two upper frame rail sections. The installer will joint the upper and lower sections together during the mock up stage of the installation. The fifth part is the rear bumper assembly. The rear bumper comes complete with 3\/4 inch thick d-ring mounts. The kit also comes with two end caps for the bumper and frame. These are welded in place to attach the rear bumper.\u003c\/p\u003e\n\u003cp\u003eAll of the parts of this kit other than the d-ring mounts are fabricated from 3\/16 inch high strength steel plate and formed on a press brake. Unlike some of the other kits on the market we do not require you to purchase square tubing to complete the project. With that said we provide a flat point on the back center of the rear bumper for the installer to triangulate some round tubing if required. The 3\/4 inch thick high strength steel plate d-ring mounts pass all the way through the rear bumper and weld in place on both sides for ultimate strength. The d-rings have a 1 inch hole in them.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJeep LJ Back Half Kit with 50 inch stubby rear bumper\u003c\/li\u003e\n\u003cli\u003e3\/16 inch high strength steel plate\u003c\/li\u003e\n\u003cli\u003ePress brake formed\u003c\/li\u003e\n\u003cli\u003e3\/4 inch thick high strength steel plate d-ring mounts\u003c\/li\u003e\n\u003cli\u003eSold as kit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eThe kit includes 7 parts total in the shipment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTwo lower frame rails sections and two upper frame rail sections\u003c\/li\u003e\n\u003cli\u003eThe installer will joint the upper and lower sections together during the mock up stage of the installation\u003c\/li\u003e\n\u003cli\u003eThe fifth part is the rear bumper assembly. The rear bumper comes complete with 3\/4 inch thick d-ring mounts\u003c\/li\u003e\n\u003cli\u003eThe kit also comes with two end caps for the bumper and frame. These are welded in place to attach the rear bumper\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThis kit will not work with the factory gas tank. Most people mount a fuel cell in the bed of the Jeep\u003c\/li\u003e\n\u003cli\u003eThe kit will not work with the factory coil springs\u003c\/li\u003e\n\u003cli\u003eThis kit is designed for more advanced Jeep builds where suspension and driving requirements demand more space and clearance\u003c\/li\u003e\n\u003cli\u003eThis kit requires an experienced welder\/fabricator to install\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271444836523,"sku":"MB3020-S-HJQL","price":749.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB3020-S-HJQL.jpg?v=1792077421"},{"product_id":"motobilt-mb3008","title":"Jeep TJ Frame Back Half Kit Motobilt","description":"\u003cp\u003eThe Motobilt Jeep TJ back half kit is the most complete on the market. This kit replaces the back section of frame rails to allow space to clear coilover shocks and increase departure angle. How does the the Jeep TJ back half kit do this? The Motobilt kit moves the frame rails from inside the wheel opening to the bottom side of the tube. In doing so the bumper location is moved up to just below the tailgate. This kit requires an experienced welder\/fabricator to install.\u003c\/p\u003e\n\u003cp\u003eBuilding custom four link suspension on a Jeep TJ does not have to be difficult. The Motobilt Jeep TJ back half kit is an effective way to gain clearance for suspension components like coilovers shocks, bypass shocks, or ORI struts. The Jeep TJ Back Half Kit moves the frame rails to the bottom side of the tube. The frame rails will mount directly to the bottom side of the rear floor board for a tight compact fit. It should be noted the kit requires cutting sheet metal on the body just below the tailgate to allow the frame rails to extend out. The bumper is then attached in this new location. The Motobilt kit comes complete with a rear bumper.\u003c\/p\u003e\n\u003cp\u003eWhat does the Motobilt Jeep TJ back half kit include? The kit includes 7 parts total in the shipment. Two lower frame rails sections and two upper frame rail sections. The installer will joint the upper and lower sections together during the mock up stage of the installation. The fifth part is the rear bumper assembly. The rear bumper comes complete with 3\/4 inch thick d-ring mounts. The kit also comes with two end caps for the bumper and frame. These are welded in place to attach the rear bumper.\u003c\/p\u003e\n\u003cp\u003eAll of the parts of this kit other than the d-ring mounts are fabricated from 3\/16 inch high strength steel plate and formed on a press brake. Unlike some of the other kits on the market we do not require you to purchase square tubing to complete the project. With that said we provide a flat point on the back center of the rear bumper for the installer to triangulate some round tubing if required. The 3\/4 inch thick high strength steel plate d-ring mounts pass all the way through the rear bumper and weld in place on both sides for ultimate strength. The d-rings have a 1 inch hole in them.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJeep TJ frame back half kit\u003c\/li\u003e\n\u003cli\u003eFabricated from 3\/16 inch high strength steel plate\u003c\/li\u003e\n\u003cli\u003ePress brake formed\u003c\/li\u003e\n\u003cli\u003e3\/4 inch thick high strength steel plate d-ring mounts\u003c\/li\u003e\n\u003cli\u003eSold as kit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eKit includes 7 parts total in the shipment\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTwo lower frame rails sections and two upper frame rail sections\u003c\/li\u003e\n\u003cli\u003eThe installer will joint the upper and lower sections together during the mock up stage of the installation\u003c\/li\u003e\n\u003cli\u003eThe fifth part is the rear bumper assembly. The rear bumper comes complete with 3\/4 inch thick d-ring mounts\u003c\/li\u003e\n\u003cli\u003eThe kit also comes with two end caps for the bumper and frame. These are welded in place to attach the rear bumper\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThis kit will not work with the factory gas tank. Most people mount a fuel cell in the bed of the Jeep\u003c\/li\u003e\n\u003cli\u003eThe kit will not work with the factory coil springs\u003c\/li\u003e\n\u003cli\u003eThis kit is designed for more advanced Jeep builds where suspension and driving requirements demand more space and clearance\u003c\/li\u003e\n\u003cli\u003eWe provide a flat point on the back center of the rear bumper for the installer to triangulate-some round tubing if required\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271445524651,"sku":"MB3008-HJQL","price":689.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB3008_5-HJQL.jpg?v=1792077425"},{"product_id":"motobilt-mb3001","title":"Jeep YJ Back Half Kit Motobilt","description":"\u003cp\u003eThe Motobilt Jeep YJ Back Half Kit is designed with function in mind. We may not be the cheapest but we certainly offer the best product on the market with years of experience to back up the product design. Motobilt is defined by high quality parts and design. The Motobilt Jeep YJ Back Half Kit was designed to meet a few different needs. The journey started about 15 years ago when Dan DuBose back halved his Jeep YJ to make more room for shocks and to gain ground clearance in the rear. Over the years the hand made design evolved into laser cut and formed parts. The design has been refined with specific goals in mind.\u003c\/p\u003e\n\u003cp\u003eThe Motobilt Jeep YJ Back Half Kit was 3D CAD designed in Solidworks for a precision fit. The parts are then CNC laser cut from 3\/16 inch thick flat steel plate, formed on a press brake, and then welded. This design and fabrication approach allows us to do things that simple box tube parts can not. The rear bumper is integrated into the design. The bumper features a very tight fitting profile with 3\/4 inch thick d-ring mounts.\u003c\/p\u003e\n\u003cp\u003eWhy installed the Motobilt Back Half Kit on your Jeep YJ? This kit provides room to mount coilover shocks and not hit the frame rails. We moved the frame rails from the factory location in the rear wheel well to under the rear floor board. This allows plenty of room to get your coilover shock angles set up correctly. Another reason is to gain about 7 inches of ground clearance in the rear bumper area.\u003c\/p\u003e\n\u003cp\u003eThis part requires extensive cutting and welding. It is recommend to have someone experienced installed this kit. It will require cutting the frame in half, cutting the body below the tailgate to allow the new frame to pass through, and welding the parts in place. Motobilt also recommends connecting your roll cage to the frame rails for added support. This kit will also require you install a fuel cell. The factory gas tank will not work with this kit.\u003cbr\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJeep YJ Back Half Kit\u003c\/li\u003e\n\u003cli\u003eFits Jeep YJ 1987-1995\u003c\/li\u003e\n\u003cli\u003eMoves frame rails under the rear floor\u003c\/li\u003e\n\u003cli\u003eImproves departure angle\u003c\/li\u003e\n\u003cli\u003eIncreases ground clearance in the rear\u003c\/li\u003e\n\u003cli\u003eIncludes a built in rear bumper\u003c\/li\u003e\n\u003cli\u003eLaser cut from 3\/16 inch steel plate\u003c\/li\u003e\n\u003cli\u003eProvides a clean place to mount air bump stops\u003c\/li\u003e\n\u003cli\u003eSold as kit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThis part requires extensive cutting and welding. It is recommend to have someone experienced installed this kit\u003c\/li\u003e\n\u003cli\u003eIt will require cutting the frame in half, cutting the body below the tailgate to allow the new frame to pass through, and welding the parts in place\u003c\/li\u003e\n\u003cli\u003eMotobilt also recommends connecting your roll cage to the frame rails for added support\u003c\/li\u003e\n\u003cli\u003eThis kit will also require you install a fuel cell. The factory gas tank will not work with this kit\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271445590187,"sku":"MB3001-HJQL","price":729.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB3001-HJQL.png?v=1792077425"},{"product_id":"motobilt-mb4059","title":"Jeep JK 1 Ton Swap Truss Kit Super Duty Dana 60 Motobilt","description":"\u003cp\u003eThe Jeep JK 1 ton axle swap kit allows you to use a 2005 and up Ford Super Duty Dana 60 front axle and install it into a Jeep Wrangler JK. It consists of a truss, upper link mounts, lower link mounts, coil spring buckets, adjustable track bar mount for the axle, track bar mount for the frame, and sway bar end link mounts. The main body of the truss is made from 1\/4 inch thick steel plate that is laser cut and CNC formed in house at Motobilt. We then brace the length of the truss with 1\/4 inch beams that closely follow every contour of the axle. Another key feature that sets us apart is the integrated and low profile diff cover. This low profile cover will work with the huge steering that comes on these 1 ton axles, yet still provides you ultimate protection. With our kit there is no measuring needed. You simply bolt the diff cover up and everything will go in place like it should. Instead of using bushings in the top, we have a flexible and rebuildable johnny joint for both upper links.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJK 1 ton axle swap kit\u003c\/li\u003e\n\u003cli\u003eThis kit allows you to use a 2005 and up Ford Super Duty Dana 60 front axle and install it into a Jeep Wrangler JK\u003c\/li\u003e\n\u003cli\u003e1\/4 inch laser cut and cnc formed\u003c\/li\u003e\n\u003cli\u003eQuick and easy no-measure install\u003c\/li\u003e\n\u003cli\u003eLow profile steel diff cover\u003c\/li\u003e\n\u003cli\u003eTrack bar mounts for both the frame and axle\u003c\/li\u003e\n\u003cli\u003eLower control arm mounts\u003c\/li\u003e\n\u003cli\u003eUpper control arm mounts with Currie Johnny Joints.\u003c\/li\u003e\n\u003cli\u003eSway bar end link mounts\u003c\/li\u003e\n\u003cli\u003eLow profile diff cover that will clear the steering\u003c\/li\u003e\n\u003cli\u003eSold as kit\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271447195819,"sku":"MB4059-HJQL","price":649.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB4059-HJQL.jpg?v=1792077441"},{"product_id":"motobilt-mb1522","title":"Jeep CJ Full Width Axle Conversion Kit Motobilt","description":"\u003cp\u003eThe Motobilt Jeep CJ full width axle conversion kit is a simple way to install a Chevy Dana 44 or Dana 60 front axle in your Jeep CJ. This kit also works with older model Ford 44 and 60 fronts from the 78\/79 range. This kit fits Jeep CJ's from 1976 to 1986. \u003cbr\u003eMotobilt offers high quality fabricated parts for the DIY fabricator. It requires welding to install. The Motobilt Jeep CJ full width axle conversion kit was designed for ultimate strength and to make your Jeep look great at the same time. The kit features an removable winch plate, 42 inch in wide fabricated bumper assembly, 3\/4 inch d-ring mounts that pass through the bumper and welded on both sides, a shackle reversal spring buckets, shackle hangers for the frame, and 4 inch long boomerang shackles. The kit moves the front axle forward as much as possible without relocating the steering box. The kit is designed to work with Jeep YJ leafs springs or Jeep CJ rear springs. The front bumper features a built in bottle opener on the bottom side.\u003cbr\u003eThe bumper, and winch plate are fabricated from 3\/16 inch high strength steel plate. The side frame plate, spring buckets, shackle hangers, and shackles are fabricated from 1\/4 inch high strength steel plate. The included d-ring mounts are fabricated from 3\/4 inch thick high strength steel plate.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJeep CJ full width axle conversion kit\u003c\/li\u003e\n\u003cli\u003eBumper and winch plate are fabricated from 3\/16 inch high strength steel plate\u003c\/li\u003e\n\u003cli\u003eSide frame plate, spring buckets, shackle hangers, and shackles 1\/4 inch high strength steel plate\u003c\/li\u003e\n\u003cli\u003eD-ring mounts are fabricated from 3\/4 inch thick high strength steel plate\u003c\/li\u003e\n\u003cli\u003eSold as kit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThis kit does not include leaf springs, u-bolts, u-bolt plates, shocks, shock mounts, poly bushings and longer brake lines. Motobilt can supply these parts for an additional price\u003c\/li\u003e\n\u003cli\u003eThis kit is Not a bolt on product\u003c\/li\u003e\n\u003cli\u003eWelding required\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271447261355,"sku":"MB1522-HJQL","price":749.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB1522-HJQL.jpg?v=1792077442"},{"product_id":"motobilt-mb1502","title":"Jeep YJ Full Width Axle Conversion Kit Motobilt","description":"\u003cp\u003eThe Motobilt Jeep YJ full width axle conversion kit is a simple way to install a Chevy Dana 44 or Dana 60 front axle in your Jeep YJ. This kit also works with older model Ford 44 and 60 fronts from the 78\/79 range. This kit fits Jeep YJ's from 1987 to 1995. Motobilt offers high quality fabricated parts for the DIY fabricator. This kit is Not a bolt on product. It requires welding to install. The Motobilt Jeep YJ full width axle conversion kit was designed for ultimate strength and to make your Jeep look great at the same time.\u003c\/p\u003e\n\u003cp\u003ehe kit features a removable winch plate, stubby front bumper assembly, 3\/4 inch d-ring mounts that pass through the bumper and welded on both sides, a shackle reversal spring buckets, shackle bushing tubes for the frame, and 4 inch long offset shackles. The kit moves the front axle forward as much as possible without relocating the steering box. The kit is designed to work with Jeep YJ leafs springs. The front bumper features a built in bottle opener on the bottom side.\u003c\/p\u003e\n\u003cp\u003eThe kit will ship with a jig to drill through the frame to locate the rear shackle hangers. This kit was designed to keep the ride height as low as possible. The rear shackle bushings will be located mid way through the frame rail. The bumper, and winch plate are fabricated from 3\/16 inch high strength steel plate. The side frame plate, spring buckets, and shackles are fabricated from 1\/4 inch high strength steel plate. The included d-ring mounts are fabricated from 3\/4 inch thick high strength steel plate.\u003cbr\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJeep YJ full width axle conversion kit to install Chevy Dana 44 or Dana 60 front axle\u003c\/li\u003e\n\u003cli\u003e1987-1995 Jeep YJ\u003c\/li\u003e\n\u003cli\u003e1978-1979 Ford 44 and 60 fronts\u003c\/li\u003e\n\u003cli\u003eBumper and winch plate 3\/16 inch high strength steel plate\u003c\/li\u003e\n\u003cli\u003eremovable winch plate\u003c\/li\u003e\n\u003cli\u003estubby front bumper assembly\u003c\/li\u003e\n\u003cli\u003eSide frame plate-spring buckets-shackles fabricated from 1\/4 inch high strength steel plate\u003c\/li\u003e\n\u003cli\u003e3\/4 inch d-ring mounts that pass through the bumper and welded on both sides\u003c\/li\u003e\n\u003cli\u003eshackle reversal spring buckets\u003c\/li\u003e\n\u003cli\u003eshackle bushing tubes for the frame\u003c\/li\u003e\n\u003cli\u003e4 inch long offset shackles\u003c\/li\u003e\n\u003cli\u003eSold as kit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThis kit is Not a bolt on product. Welding required to install.\u003c\/li\u003e\n\u003cli\u003eThis kit does not include leaf springs, u-bolts, u-bolt plates, shocks, shock mounts, poly bushings and longer brake lines. Motobilt can supply these parts for an additional price.\u003c\/li\u003e\n\u003cli\u003eThe front bumper features a built in bottle opener on the bottom side\u003c\/li\u003e\n\u003cli\u003eThe kit will ship with a jig to drill through the frame to locate the rear shackle hangers\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271447425195,"sku":"MB1502-HJQL","price":699.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB1502-HJQL.jpg?v=1792077445"},{"product_id":"motobilt-mb3025","title":"Jeep JK \u0026 JKU Back Half Kit 07-18 Wrangler JK Motobilt","description":"\u003cp\u003eThis cutting edge design is the first of its kind for the Jeep JK. The kit replaces the entire back half of the frame from below the doors to the rear bumper. The Motobilt Jeep JK back half kit was 3 D cad designed by our legendary team of experts. The three main factors considered in the design were room for coil over shocks, a rear mounted fuel cell, and the ability to mount a true 4 link suspension.\u003cbr\u003e\u003cstrong\u003eThe kit includes:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePassenger side frame rails. 2 pcs\u003c\/li\u003e\n\u003cli\u003eDriver side frame rails. 2 pcs\u003c\/li\u003e\n\u003cli\u003eFrame rail connecting plates 2 pcs\u003c\/li\u003e\n\u003cli\u003eRear cross member 1 pcs\u003c\/li\u003e\n\u003cli\u003eFrame chop rear bumper 1 pcs\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWorks with both the 2 door JK or the 4 door JKU\u003c\/li\u003e\n\u003cli\u003eFrame rails above axle center line are moved inwards 5 inches per side allowing room for coil overs.\u003c\/li\u003e\n\u003cli\u003eRoom for single or dual shocks.\u003c\/li\u003e\n\u003cli\u003eMain frame rails include 2 new body mounts that are matched to the OEM specifications for precision.\u003c\/li\u003e\n\u003cli\u003eTwo of the factory body mounts over the axle are removed.\u003c\/li\u003e\n\u003cli\u003e4 frame cross members are removed allowing room for more axle travel upward. This allows a lower center of gravity.\u003c\/li\u003e\n\u003cli\u003eThe new 3\/16 inch thick steel frame rails provide a much stronger mounting point for link mounts then the thin weak factory frame rails.\u003c\/li\u003e\n\u003cli\u003eAn optional cross member to mount 4 link mounts will be available soon.\u003c\/li\u003e\n\u003cli\u003eAn optional aluminum fuel cell with 3\/16 inch thick steel plate skid plate will be available soon. An OEM sending unit will be compatible with the new cell.\u003c\/li\u003e\n\u003cli\u003ePrecise easy to locate points for cutting the factory frame rails are provided and alignment holes are in place to make the install fool proof.\u003c\/li\u003e\n\u003cli\u003eThe install requires the frame to be cut with a saw and not a torch. This makes for a clean, quick, and precise install.\u003c\/li\u003e\n\u003cli\u003eThe rear frame rails are shortened 2.5 inches over stock and moved up 1 1\/8 inches.\u003c\/li\u003e\n\u003cli\u003eWill work with Antirock sway bar kit for JK\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNotes:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eYour stock exhaust will have to be modified\u003c\/li\u003e\n\u003cli\u003eRequires cutting and welding\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271448506539,"sku":"MB3025-HJQL","price":1709.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB3025-HJQL.jpg?v=1792077470"},{"product_id":"motobilt-mb3034","title":"Jeep TJ-LJ Front Half Frame Kit For 97-06 Wrangler TJ and Unlimited Motobilt","description":"\u003cp\u003eMB3034 Jeep TJ-LJ Front Half Frame Kit. The Motobilt MB3034 Jeep TJ-LJ Front Half Frame Kit is an innovative weld-on front steel frame replacement\/upgrade for the hard core builder who wants to transform their Jeep TJ-LJ into a true off-road beast.\u003c\/p\u003e\n\u003cp\u003eWhen swapping to larger, heavier duty front axles to accommodate large 40 inch or 42 inch tires in a Jeep TJ or LJ, it has become more and more common to move the front axle forward a few inches to provide increased upwards travel of the axle, suspension and steering components, as well as, increasing the overall wheelbase of the vehicle for stability.\u003c\/p\u003e\n\u003cp\u003eThis kit facilitates extra clearance for a true 4 link front suspension system. This essentially allows you to lower the overall center of gravity of your vehicle, which, as true hard core wheelers know, is the key to building a very capable off-road vehicle.\u003c\/p\u003e\n\u003cp\u003eThis premium builder solution takes all of the guess work out of this potentially daunting task. Designed using the very latest 3D CAD technology along with CAD files direct from Chrysler\/Jeep, our team of highly experienced professionals (who are also hard core wheelers, builders and fabricators) have engineered a precision product that simply makes your off road vehicle perform to its peak potential.\u003c\/p\u003e\n\u003cp\u003eThe boxed in C-Channel design of our kit is manufactured from high grade 3\/16 inch thick steel that is laser cut and precision CNC press brake formed. The C-Channel design fits over and laps portions of the stock frame where it is then welded permanently in place. The inner plates of the frame feature slotted weep holes to aid in cleaning and maintenance.\u003c\/p\u003e\n\u003cp\u003eWe provide detailed step-by-step instructions with photos showing where to mark and cut your existing stock TJ-LJ frame. Our kit includes locating holes which allow you to precisely position your new front frame by using existing threaded bolt hole locations in the stock frame.\u003c\/p\u003e\n\u003cp\u003eThe up swept design of the MB3034 Jeep TJ-LJ Front Half Frame Kit relocates the forward-most portion of the stock frame by moving it upwards. This means there is essentially NO approach angle caused by the frame or front bumper. The front tires are the first point of contact on any obstacle. Game changer.\u003c\/p\u003e\n\u003cp\u003eThe integrated front bumper of our kit is designed to fit a large recovery winch like the Warn Zeon 12S (or similar). The winch mount is recessed to provide protection for the winch and to provide the most airflow to the radiator.\u003c\/p\u003e\n\u003cp\u003eThe winch mounting bolts are recessed and protected from trail damage. We have included a forward facing Hawse Fairlead mount into the front bumper design, along with a separate lower opening located under the winch which gives you the ability to run your winch line straight down to the axle. For years, hard core wheelers and professional rock crawlers have been using this technique of using the winch to suck the front end down to the axle when tackling steep obstacles to change your center of gravity.\u003c\/p\u003e\n\u003cp\u003eWe have integrated this feature into this kit to make it easy. Also integrated into the front bumper design are two (2) 3\/4 inch thick high grade steel D-Ring mounts for recovery. The D-Ring plates are elongated back into the recess of the winch mount to increase the welding area for strength and to provide an additional degree of structural stability to the front frame.\u003c\/p\u003e\n\u003cp\u003eYou will be removing your stock front upper shock mounts to make room for longer coil over shocks, providing space for high clearance outer fenders, and potentially removing 3 inch from your stock hood, which, in turn, provides ample inchup-travel inch clearance for larger 40 inch-42 inch tires to articulate through its suspension cycle on larger axles. Motobilt offers solutions to help you in these stages.\u003c\/p\u003e\n\u003cp\u003eThis kit requires cutting and removing the front portion of your existing stock frame, chopping your existing engine mounts and replacing them (engine mounts not included in kit). The kit dimensionally works with the stock engine or a variety of aftermarket crate engines like LS or Hemi.\u003c\/p\u003e\n\u003cp\u003eThis kit is intended for full hydro steering systems. It does not use a mechanical steering system. The reason for changing to a full hydro steering system is to provide ample turning force when using large tires, to remove obstructions for increased inchup travel inch of the front axle and to eliminate mechanical steering linkages that are prone to hitting on obstacles resulting in breakages. This kit cleans up the entire front end and gives you a stable and strong new structure that is purpose built for rock crawling.\u003c\/p\u003e\n\u003cp\u003eWelding and finishing is required. We recommend welding be performed by a qualified welder. You will be reusing your stock grill and notching it to fit around the new front frame members. An aftermarket radiator is strongly suggested.\u003cbr\u003eThis product is shipped as three (3) pre-welded assemblies and two (2) loose flat plates. Welding is required to marry all pieces to the modified frame. \u003cbr\u003eWeight = 75 lbs\u003c\/p\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271453454507,"sku":"MB3034-HJQL","price":849.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB3034-HJQL.jpg?v=1792077554"},{"product_id":"motobilt-mb3067","title":"15 Inch Stretch Back Half Frame Kit for Jeep YJ Motobilt","description":"\u003cp\u003eWant to stretch your Jeep YJ to be the same length as a Jeep LJ? Where do I start? You start with a great foundation - The Frame.\u003c\/p\u003e\n\u003cp\u003eThis American made kit narrows the width of the frame by 8-1\/16 inch less than the factory YJ frame and extends the length of the frame rearward by 15 inch.\u003c\/p\u003e\n\u003cp\u003eThis provides ample room to install coil-over shocks that are positioned outboard of the frame and allow the space necessary to build your much longer custom 4 link rear suspension system to help keep the tires in contact with ground while increasing your wheel articulation.\u003c\/p\u003e\n\u003cp\u003eThe new longer wheelbase of your vehicle will greatly increase the stability and off-road capabilities of your YJ for hard core rock crawling.\u003c\/p\u003e\n\u003cp\u003eThis is a builder kit. Professional fabrication and\/or welding is recommended. This kit includes four (4) sections of new frame rails constructed using 3\/16 inch high grade steel that is precision CNC laser cut and expertly formed on our CNC press brake, then professionally welded, sanded and inspected at our state-of-the-art fabrication facility.\u003c\/p\u003e\n\u003cp\u003eAlso included is a new fully welded heavy duty rear bumper with integrated ѕ inch thick recovery mounts built in. There are also two side plates included that reinforce the join between the rear bumper and the frame rails for added strength. The new frame rails include two (2) relocated body mount holes.\u003c\/p\u003e\n\u003cp\u003eOur step-by-step assembly instructions facilitate the entire process. We show you where and how to cut your existing frame, where to make cut outs in the body for the new frame to pass through, measurements on how to square up the frame and then where to place all of your finish welds.\u003c\/p\u003e\n\u003cp\u003eThe YJ body will also get cut and moved rearward by 15 inch. This kit does not cover this process. All parts ship as raw steel. Welding is required. You will not be able to return your vehicle back to factory after this modification.\u003cbr\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e15 Inch Stretch Back Half Frame Kit for Jeep YJ\u003c\/li\u003e\n\u003cli\u003eMaterial: Steel\u003c\/li\u003e\n\u003cli\u003eFinish: Bare\u003c\/li\u003e\n\u003cli\u003eSize: 15.0 Inch\u003c\/li\u003e\n\u003cli\u003eFits: 1987-1996 Jeep Wrangler YJ\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271463481515,"sku":"MB3067-HJQL","price":779.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB3067-HJQL.jpg?v=1792077778"},{"product_id":"motobilt-mb3020-w","title":"Back Half Frame Kit w\/ Wide Bumper for 04-06 Jeep LJ Motobilt","description":"\u003cp\u003eThe Motobilt Jeep LJ back half kit is the most complete on the market. This kit replaces the back section of frame rails to allow space to clear coilover shocks and increase departure angle. How does the the Jeep LJ back half kit do this? The Motobilt kit moves the frame rails from inside the wheel opening to the bottom side of the tube. In doing so the bumper location is moved up to just below the tailgate. This kit requires an experienced welder\/fabricator to install.\u003c\/p\u003e\n\u003cp\u003eBuilding custom four link suspension on a Jeep LJ does not have to be difficult. The Motobilt Jeep LJ back half kit is an effective way to gain clearance for suspension components like coilovers shocks, bypass shocks, or ORI struts. The Jeep LJ Back Half Kit moves the frame rails to the bottom side of the tube. The frame rails will mount directly to the bottom side of the rear floor board for a tight compact fit.\u003c\/p\u003e\n\u003cp\u003eIt should be noted the kit requires cutting sheet metal on the body just below the tailgate to allow the frame rails to extend out. The bumper is then attached in this new location. The Motobilt kit comes complete with a rear bumper. The wide version is for those who are not going to stretch their wheelbase.\u003c\/p\u003e\n\u003cp\u003eWhat does the Motobilt Jeep LJ back half kit include? The kit includes 7 parts total in the shipment. Two lower frame rails sections and two upper frame rail sections. The installer will joint the upper and lower sections together during the mock up stage of the installation. The fifth part is the rear bumper assembly. The rear bumper comes complete with 3\/4 inch thick d-ring mounts. The kit also comes with two end caps for the bumper and frame. These are welded in place to attach the rear bumper.\u003c\/p\u003e\n\u003cp\u003eAll of the parts of this kit other than the d-ring mounts are fabricated from 3\/16 inch high strength steel plate and formed on a press brake. Unlike some of the other kits on the market we do not require you to purchase square tubing to complete the project.\u003c\/p\u003e\n\u003cp\u003eWith that said we provide a flat point on the back center of the rear bumper for the installer to triangulate some round tubing if required. The 3\/4 inch thick high strength steel plate d-ring mounts pass all the way through the rear bumper and weld in place on both sides for ultimate strength. The d-rings have a 1 inch hole in them.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eBack Half Frame Kit w\/ Wide Bumper\u003c\/li\u003e\n\u003cli\u003eFits: 04-06 Jeep LJ\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271489401003,"sku":"MB3020-W-HJQL","price":809.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB3020-W-HJQL.jpg?v=1792078099"},{"product_id":"motobilt-mb4058","title":"14 Bolt One Ton Conversion Truss w\/ pinion guard for Jeep JK Rear Motobilt","description":"\u003cp\u003eThe Motobilt Jeep JK rear 1 ton axle swap with pinion guard makes installing a beefy rear axle in your Jeep a breeze. When designing our kit we wanted it to be easy to install. Whether you are a professional shop or are a DIY fabricator at home, this kit will save you time and money. Our kit spans much further across the axle than other kits on the market.\u003c\/p\u003e\n\u003cp\u003eThis allowed us to incorporate the spring mounts into the truss. You will simply bolt the pinion support onto the axle and then set all of the other components onto the top. With the aligning tabs and slots, the installation is foolproof.\u003c\/p\u003e\n\u003cp\u003eThe kit was designed to work with the GM 14 bolt rear axle that was found in 1996-2006 GM 2500 and 3500 Single Rear Wheel axle trucks. The wheel mounting surface (WMS) will be 68 inches wide and the casting on the center differential has lots of ribbing.\u003c\/p\u003e\n\u003cp\u003eDo not use an axle from a van as the differential is offset. When installing this axle, remember that you will need to address things such as the 8x6.5 bolt pattern vs. the Jeep's factory 5x5 bolt pattern.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJK Rear 1 Ton axle swap with pinion guard\u003c\/li\u003e\n\u003cli\u003eDesigned to work with the GM 14 bolt rear axle that was found in 1996-2006 GM 2500 and 3500 Single Rear Wheel axle trucks\u003c\/li\u003e\n\u003cli\u003eThe axle truss ships raw steel and will require professional welding\u003c\/li\u003e\n\u003cli\u003eLaser cut and CNC formed from 1\/4 inch thick steel plate\u003c\/li\u003e\n\u003cli\u003eIntegrated coil spring mounts with truss\u003c\/li\u003e\n\u003cli\u003eEasy install with no measurements needed\u003c\/li\u003e\n\u003cli\u003eTrack bar includes 4 mounting locations in case you change up your suspension\u003c\/li\u003e\n\u003cli\u003eMain truss body is one solid piece with several support beams made of 1\/4 inch steel plate\u003c\/li\u003e\n\u003cli\u003eCoil spring mounts have a built-in threaded nut to use with a spring retainer\u003c\/li\u003e\n\u003cli\u003eUpper and lower link mounts are formed so that your suspension is still in alignment once the wider axles are installed\u003c\/li\u003e\n\u003cli\u003eCan easily be changed if you want to run a custom suspension design\u003c\/li\u003e\n\u003cli\u003eSold as kit\u003c\/li\u003e\n\u003cli\u003eWeight: 80lbs (approx.)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe pinion guard will hit the factory gas tank unless you stretch the wheelbase and move the rear axle back or relocate the gas tank.\u003c\/li\u003e\n\u003cli\u003eOptional HD steel diff cover (MB4012) is NOT included.\u003c\/li\u003e\n\u003cli\u003eBrake components such as the tone rings and ABS sensors will need to be addressed as they are not included in this kit\u003c\/li\u003e\n\u003cli\u003eAxle assembly shown is NOT included and is only shown for demonstration purposes.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271491891371,"sku":"MB4058-HJQL","price":579.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB4058-HJQL.jpg?v=1792078157"},{"product_id":"motobilt-mb1522-s","title":"Jeep CJ Full Width Axle Conversion Kit W\/Stinger Motobilt","description":"\u003cp\u003eThe Motobilt Jeep CJ full width axle conversion kit is a simple way to install a Chevy Dana 44 or Dana 60 front axle in your Jeep CJ. This kit also works with older model Ford 44 and 60 fronts from the 78\/79 range. This kit fits Jeep CJ's from 1976 to 1986.\u003c\/p\u003e\n\u003cp\u003eMotobilt offers high quality fabricated parts for the DIY fabricator. It requires welding to install. The Motobilt Jeep CJ full width axle conversion kit was designed for ultimate strength and to make your Jeep look great at the same time.\u003c\/p\u003e\n\u003cp\u003eThe kit features an removable winch plate, 42 inch in wide fabricated bumper assembly, 3\/4 inch d-ring mounts that pass through the bumper and welded on both sides, a shackle reversal spring buckets, shackle hangers for the frame, and 4 inch long boomerang shackles.\u003c\/p\u003e\n\u003cp\u003eThe kit moves the front axle forward as much as possible without relocating the steering box. The kit is designed to work with Jeep YJ leafs springs or Jeep CJ rear springs. The front bumper features a built in bottle opener on the bottom side.\u003c\/p\u003e\n\u003cp\u003eThe bumper, and winch plate are fabricated from 3\/16 inch high strength steel plate. The side frame plate, spring buckets, shackle hangers, and shackles are fabricated from 1\/4 inch high strength steel plate. The included d-ring mounts are fabricated from 3\/4 inch thick high strength steel plate.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJeep CJ full width axle conversion kit with stinger\u003c\/li\u003e\n\u003cli\u003eBumper and winch plate are fabricated from 3\/16 inch high strength steel plate\u003c\/li\u003e\n\u003cli\u003eSide frame plate, spring buckets, shackle hangers, and shackles 1\/4 inch high strength steel plate\u003c\/li\u003e\n\u003cli\u003eD-ring mounts are fabricated from 3\/4 inch thick high strength steel plate\u003c\/li\u003e\n\u003cli\u003eSold as kit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThis kit does not include leaf springs, u-bolts, u-bolt plates, shocks, shock mounts, poly bushings and longer brake lines. Motobilt can supply these parts for an additional price\u003c\/li\u003e\n\u003cli\u003eThis kit is Not a bolt on product\u003c\/li\u003e\n\u003cli\u003eWelding required\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271492186283,"sku":"MB1522-S-HJQL","price":889.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB1522-S_0-HJQL.jpg?v=1792078170"},{"product_id":"motobilt-mb1502-s","title":"Jeep YJ Full Width Axle Conversion Kit W\/Stinger Motobilt","description":"\u003cp\u003eThe Motobilt Jeep YJ full width axle conversion kit is a simple way to install a Chevy Dana 44 or Dana 60 front axle in your Jeep YJ. This kit also works with older model Ford 44 and 60 fronts from the 78\/79 range. This kit fits Jeep YJ's from 1987 to 1995. Motobilt offers high quality fabricated parts for the DIY fabricator. This kit is Not a bolt on product. It requires welding to install. The Motobilt Jeep YJ full width axle conversion kit was designed for ultimate strength and to make your Jeep look great at the same time.\u003c\/p\u003e\n\u003cp\u003ehe kit features a removable winch plate, stubby front bumper assembly, 3\/4 inch d-ring mounts that pass through the bumper and welded on both sides, a shackle reversal spring buckets, shackle bushing tubes for the frame, and 4 inch long offset shackles. The kit moves the front axle forward as much as possible without relocating the steering box. The kit is designed to work with Jeep YJ leafs springs. The front bumper features a built in bottle opener on the bottom side.\u003c\/p\u003e\n\u003cp\u003eThe kit will ship with a jig to drill through the frame to locate the rear shackle hangers. This kit was designed to keep the ride height as low as possible. The rear shackle bushings will be located mid way through the frame rail. The bumper, and winch plate are fabricated from 3\/16 inch high strength steel plate. The side frame plate, spring buckets, and shackles are fabricated from 1\/4 inch high strength steel plate. The included d-ring mounts are fabricated from 3\/4 inch thick high strength steel plate.\u003cbr\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJeep YJ full width axle conversion kit to install Chevy Dana 44 or Dana 60 front axle with Stinger\u003c\/li\u003e\n\u003cli\u003e1987-1995 Jeep YJ\u003c\/li\u003e\n\u003cli\u003e1978-1979 Ford 44 and 60 fronts\u003c\/li\u003e\n\u003cli\u003eBumper and winch plate 3\/16 inch high strength steel plate\u003c\/li\u003e\n\u003cli\u003eremovable winch plate\u003c\/li\u003e\n\u003cli\u003estubby front bumper assembly\u003c\/li\u003e\n\u003cli\u003eSide frame plate-spring buckets-shackles fabricated from 1\/4 inch high strength steel plate\u003c\/li\u003e\n\u003cli\u003e3\/4 inch d-ring mounts that pass through the bumper and welded on both sides\u003c\/li\u003e\n\u003cli\u003eshackle reversal spring buckets\u003c\/li\u003e\n\u003cli\u003eshackle bushing tubes for the frame\u003c\/li\u003e\n\u003cli\u003e4 inch long offset shackles\u003c\/li\u003e\n\u003cli\u003eSold as kit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThis kit is Not a bolt on product. Welding required to install.\u003c\/li\u003e\n\u003cli\u003eThis kit does not include leaf springs, u-bolts, u-bolt plates, shocks, shock mounts, poly bushings and longer brake lines. Motobilt can supply these parts for an additional price.\u003c\/li\u003e\n\u003cli\u003eThe front bumper features a built in bottle opener on the bottom side\u003c\/li\u003e\n\u003cli\u003eThe kit will ship with a jig to drill through the frame to locate the rear shackle hangers\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271492219051,"sku":"MB1502-S-HJQL","price":839.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB1502-S-HJQL.jpg?v=1792078171"},{"product_id":"motobilt-mb3080","title":"Mid Frame Section for Jeep YJ\/TJ\/LJ Motobilt","description":"\u003cp\u003eLooking to build out a complete Motobilt frame? The foundation starts with the Motobilt Mid Frame Section for the Jeep YJ, TJ, and LJ. Designed to work with the Motobilt front half and back half kits, this heavy-duty section provides the strength and precision fit needed to upgrade your rig's foundation.\u003c\/p\u003e\n\u003cp\u003eFabricated from 3\/16 inch thick American steel, the MB3080 is built to handle extreme off-road use and the rigors of trail abuse. Often when building a custom Jeep YJ, TJ, or LJ you find out that the center section is rusted out or damaged so what do you do? That's where the mid frame section comes in as it's a heavy duty center section designed to work with the Motobilt front and back half kits.\u003c\/p\u003e\n\u003cp\u003eWhy buy a rusted out or expensive factory Jeep frame when you are building a hardcore off road rig? Many customers will use this frame section along with a back half kit to convert from a YJ or TJ to the LJ length or what's referred to as an TJ-6.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHighlights:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMade in the USA\u003c\/li\u003e\n\u003cli\u003e3\/16 inch Steel Construction\u003c\/li\u003e\n\u003cli\u003eAllows you to build a complete frame\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eFits:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eJeep YJ\u003c\/li\u003e\n\u003cli\u003eJeep TJ\u003c\/li\u003e\n\u003cli\u003eJeep LJ\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCompatible:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFront Half Kit: MB3034\u003c\/li\u003e\n\u003cli\u003eBack Half Kit: MB3008 (TJ), MB3001 (YJ), MB3020-S\/MB3020-W (LJ)\u003c\/li\u003e\n\u003cli\u003eSuspension: MB7009 (YJ\/TJ\/LJ) Double Triangulated 4 link\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWeight: 77 lbs\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNotes:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eShips raw steel; must be painted or powder coated to prevent rust.\u003c\/li\u003e\n\u003cli\u003eThis is NOT a factory replacement frame section to repair your damaged or rusted frame.\u003c\/li\u003e\n\u003cli\u003eWelding required for installation.\u003c\/li\u003e\n\u003cli\u003eProfessional installation recommended for proper alignment and fitment.\u003c\/li\u003e\n\u003cli\u003eDoes not include body mounts or threaded skid plate mounting holes. Recommended: YJ-MB3081 Body mounts. TJ\/LJ -MB3035 Body Mounts\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":48271495757995,"sku":"MB3080-HJQL","price":839.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/files\/MB3080-HJQL.jpg?v=1792078265"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0245\/1731\/2593\/collections\/MB1502-S-HJQL_bee21ae4-95e8-4061-bdc9-89a827e12fb1.jpg?v=1792192484","url":"https:\/\/dev-arw-off-road.myshopify.com\/collections\/fabrication-chassis-axle-conversion.oembed","provider":"ARW Offroad","version":"1.0","type":"link"}